Finish Room Explosion Proof Exhaust Fan With Heat Source

Heaters for the Harshest Environments

EFX

Explosion-Trial impression

Consume Fan

This manual covers installations, maintenance, repair and replacement parts.

WARNING!

Register ALL IMPORTANT NOTICES Connected PAGE 3.

Delight ADHERE TO Operating instructions PUBLISHED IN THIS MANUAL.

Failure to do and so Crataegus laevigata constitute dangerous and may void doomed commissariat of your warranty.

Ruffneck ™ is a tonality brand of CCI Outpouring Technologies Inc.

Right of first publication © 2013. All rights reserved.

Split up None. 10356.Rev.1.02

Written in Canada

FAN MAINTENANCE CHECKLIST

For Explosion-Proof Exhaust Fan

Admonitory

Fan should only be serviced by qualified personnel with HVAC equipment experience. Disconnect fan from power render ahead servicing fan. Ignition lock the switch in the "OFF" (open) set out and/or tag the replacement to prevent unexpected power application program.

Cyclic (before and as obligatory during heating season)

1. CLEAN	Fan	2. Suss out	Motor for glassy, serenity operation
	Winnow Guard		Dampers for decorous angle and tautness
	Motor
	Backdraft Dampers
	Stormhood

Remove dust using compressed breeze. Do non nebulise with water or solvents.

ANNUAL (before heating season)

1. ELECTRICAL

Curb every last terminal connections and conductors. Tighten friable connections. Conductors with damaged insulation must be replaced.

2. MECHANICAL

Check motor shaft bearing play. Replace motor if represent is exuberant or motor does not run restfully and smoothly. Motor bearings are permanently lubricated.

Chequer fan. Replace immediately if cracked or discredited.

Check the tightness of all computer hardware. All nuts and bolts, including mounting hardware, must live tight.

TURN Buff Along FOR A MINIMUM OF 15 Proceedings. Check for air exiting fan through and through dampers and smooth running of fan motor.

Heaters for the Harshest Environments

For assistance, please call Toll Free: 1-800-661-8529 (24 hrs)

U.S. & Canada

- 2 -

Heavy NOTICES

Admonitory:

Read and adhere to the following. Failure to do so may result in bad or fatal injury.

1. Learn and keep up the instruction manual in this manual.

2. Fan(s) are to be installed and serviced only

by qualified personnel experienced in electric and HVAC work.

3. Installation and wiring of the lover must adhere to wholly applicable codes.

4. It is essential that any winnow, that will follow used

in a hazardous (classified) location, is helmeted with an electric motor authorized for such service.

5. Do not operate fan in atmospheres which are destructive to nerve or atomic number 13, unless it has been coated with a factory approved protecting coating.

6. Buff moldiness be kept clean. When operating in a dirty environment, regularly clean fan and fan guard. Follow the suggested sustenance procedures. Consult to the "Fan Maintenance Checklist" section for details.

7. Use manufacturing plant approved replacement parts only.

8. If thither are any questions or concerns regarding the winnow, contact the factory. Refer to the cobbler's last foliate of this manual for details.

W A R R A N T Y W I L L B E V O I D

I F I N S T R U C T I O N S A R E N O T F O L L O W E D

INSTALLATION

The installation instructions allow a general guideline for the installation and wiring of the run down fan. All applicable codes must be adhered to.

Placement

1. For optimum melody exhaust, the fan(s) should atomic number 4 installed as follows:

a. There are no obstructions that may impede the fans air inlet or run.

b. The air discharge is directed departed from building.

c. The air discharge is not manageable at a thermostat.

d. For warehouses or large workshops it may personify satisfactory to use fewer, larger fans.

2. This unit can exhaust warm Beaver State cool publicize depending on customer conditions. Be aware of problems each can produce.

Climb

1. The Tucker Fan is designed to beryllium installed in an upright and level emplacement.

2. Fan(s) are designed to be mounted from the rear using four 3/8" holes. For fan dimensions,

see Figure 2.

3. The mounting structure must be strong enough to:

a. Support the fans weight

(advert to the specification section).

b. Provide adequate rigorousness to prevent excessive vibration.

c. Withstand abusive situations such American Samoa transportable installations.

d. If Exhaust Fan is installed on a paries thinner than 4", customer will need to install shims to bring face of fan away from climb surface.

- 3 -

						G
	D
		B	F
	C
	A
	AIR FLOW
	DIMENSION			EFX-12	EFX-16 EFX-20 EFX-24			EFX-30
		A	mm	392.1	377.8	409.6	393.7	396.9
			in	15.4	14.9	16.1	15.5	15.6
	E	B	mm	461.9	588	687.9	787.9	942.3
			in	18.2	23.2	27.1	31	37.1
		C	mm	410	512.5	614.5	714.5	862.5
			in	16.1	20.2	24.2	28.1	34
		D	mm	79.4	57.2	91.7	76.2	88.9
			in	3.1	2.2	3.6	3	3.5
	*	E	mm	373.3	475.6	577.3	677.3	835.3
			in	14.7	18.7	22.7	24.7	32.9
		F	millimeter	411.1	537.2	637.1	737.1	891.5
			in	16.2	21.2	25.1	29	35.1
		G	mm	359.2	461.7	563.7	663.7	811.7
			in	14.1	18.2	22.2	26.1	32
	* This dimension is the lower limit square opening size

Anatomy 2

MOUNTING CLEARANCES

1. Leave leastwise 20" (500mm) headroom between the rear of the motor and the nearest obstruction.

2. Clearance equal to the height of the fan shroud above, or beneath is required for easy fan or motor replacement.

TEMPERATURE Curb

1. If required, the fan outturn may live thermostatically controlled past a remotely mounted thermostat.

FINAL INSPECTION

1. Earlier application of electrical power:

a. Check that completely connections are secured and abide by with the applicable wiring diagram and code requirements

b. Substantiate the power supply is compatible with the data plate rotating on motor.

c. Remove whatsoever foreign objects from fan.

d. Secure all electrical covers are well bonded.

e. Ensure the buff rotates freely counterclockwise when viewed from the rear of the fan and air exits through the dampers.

- 4 -

Finish Room Explosion Proof Exhaust Fan With Heat Source

Source: https://manualmachine.com/ccithermaltechnologies/efxexplosionproofexhaustfan/1387385-user-manual/

Share this post